Your Cart

No products in the cart.

Return To Shop
0

Offer ends in

Days
Hours
Minutes

Repair Guides

How to change the power inlet fuse

This article will guide you to changing power inlet fuse as well as the plug fuse. Before following this guide it is a good idea to find the cause of the blown fuse and we suggest reading the circuit overload article. What will I need? To undertake the replacement you

Read More »

Motor Alignment

This page helps you to align your motor 90 degrees with the motor belt if it looks slightly mis-aligned. Misalignment of more than 5 degrees can cause belt squeak. Some key components that need to be considered when addressing the motor alignment are listed below: 1. Motor The main electric motor

Read More »
E8 Series
NoblePro Support

Replacing Screen

This guide will walk you through how swap over your screen.  If you need further assistance or details on the process, please refer to the relevant user manual. What will I need: Replacement screen Star screwdriver 5mm allen key Replacing the screen Step 1: Remove the 2 screws that fasten

Read More »
E8 Series
SvB

Replacing Screen to Console Cable

This guide will walk you through how to fit the console cables between the NoblePro Elite E8i series treadmill screen and the console buttons. What will I need: Replacement cable Screwdriver Replacing the cable Step 1: Unscrew the 7 screws from the back of the screen. Step 2: The back

Read More »

How to replace a kicker or gas strut

This is a step by step guide how to replace the kicker or entire gas strut assembly. The kicker is the plastic component on the gas struct what you push when you want the treadmill to go down. The gas struct enables the treadmill to slowly lower from the storage

Read More »
E8 Series
SvB

Replacing a incline motor

This page contains the instructions to replace the incline motor [56] for the NoblePro Elite Series (NPE78848E8is, NPE78844E8i, NPE78847E8s, NPE78843E8.0). WARNING: Mains voltage can be dangerous. Ensure the needed safety precautions are taken before undertaking these instructions. What will I need? To undertake the replacement you will need: 1. Replacement

Read More »
Bluetooth
NoblePro Support

How to fit a Bluetooth BLE HRM V2 module

This guide will walk you through how to fit a BLE Bluetooth HRM V2 module for NoblePro Elite E8 series treadmills. There modules were fitted as of 26th Dec 2021. This will allow HRM BLE enabled apps to get heart rate data from the treadmill to enable viewing of your

Read More »
E8.0 Console
NoblePro Support

Fitting an FTMS + Audio Bluetooth V3

This guide will walk you through how to fit a FTMS + Audio Bluetooth V3 module for NoblePro Elite E8.0 series treadmills. These modules are FTMS compatible to allow connection to virtual foot pods, the sending of data to BLE HRM and Bluetooth audio in. For further information on the

Read More »

Rear Roller Replacement

This page contains the instructions to replace the rear roller [81] for the NoblePro Elite Series treadmills (NPE78848E8is, NPE78844E8i, NPE78847E8s, NPE78843E8.0). What will I need? To undertake the replacement you will need: Replacement rear roller. 6mm allen key Remember: Part will be reused. Keep all the parts removed, besides the

Read More »
E8i Console
NoblePro Support

Fitting an FTMS + Audio Bluetooth V3

This guide will walk you through how to fit an FTMS + Audio Bluetooth V3 module for NoblePro Elite E8i series treadmills. These modules are FTMS compatible to allow connection to virtual foot pods, the sending of data to BLE HRM and Bluetooth audio in. For further information on the

Read More »

Contact NoblePro Support

Need help? Starting your support request online and we’ll connect you to the Support Team.